California Fencing Contractor (C-13) License Practice Exam

These questions are part of the practice quiz. Start practicing

• What maintenance is required for vinyl fences?
• How does the Mechanics Lien law relate to fencing contractors in California?
• How should drainage and grading influence fence installation?
• What is the best bolt to use for a brace band?
• What is the role of end posts versus line posts in chain-link fencing?
• How are fence line and gate locations determined from a site plan?
• Typical fence line posts should be set in undisturbed earth by _______.
• Which type of insurance and bonding are generally required for a California fencing contractor to operate legally?
• How are gate openings measured on chain link fences?
• What arithmetic operation determines how many top rail pieces are required from total length and piece length?
• Which agency's specifications are cited for testing and fence-related requirements in these examples?
• Which length and tolerance is specified for roll chain link fence material under ASTM standards?
• When ornamental iron is installed onto or through wood, what should be avoided?
• What is the length for a roll chain link fence material, according to ASTM standards?
• What installation considerations are unique to vinyl fencing?
• Which if the following statements about caps on tubular posts is NOT correct?
• Which items are cited as differences between hanging wood gates and iron/metal gates?
• What is the best way to remove an existing post?
• What is a major benefit of metal ornamental fences?
• Why is drainage and ventilation around posts important for wooden fences?
• To remove an existing post with a concrete base, which tool is best?
• Which two CSLB exams are typically required to obtain the C-13 Fencing Contractor license?
• What is the proper way to install a tap?
• According to CalTrans, posts from each lot must be tested up to which number?
• Which of the following aren't used with wood gates?
• How should posts be treated to resist rot at ground level?
• The corners of the gate frames should be fastened together and reinforced with which option?
• Where do you put a turnbuckle on a wood gate frame?
• Which method is recommended to connect fabric to wrought metal parts in fencing?
• When reading project plans for a fence installation, what is typically shown in the site plan?
• Which tool is used to cut sheet steel?
• In vinyl fencing, which factor most influences long-term stability in wet climates?
• Sheet steel is cut with a ___ and bent into the desired shape with ___?
• According to CalTrans, all earth, trees, brushes, and other obstructions that interfere with the proper construction of fences:
• Present day wrought metal items are usually made of hot rolled, low carbon steel or duct alloys of which two materials?
• To which side effects of the posts should wire mesh fabric be attached, according to CalTrans?
• Before assembling them, which action should be taken on metal where two pieces touch?
• Which material is described as offering superior corrosion resistance and low maintenance?
• How is post spacing calculated for a typical wood picket fence?
• How should vinyl fence posts be anchored, and what is the role of footings?
• Which of the following is recommended for maximum post security?
• Entry gates usually swing which direction?
• Gate latches must be made of which materials?
• Which statement about the CSLB is true?
• What are typical advantages of vinyl fencing compared to wood?
• In residential fencing plans, which scale option is not commonly used?
• Which wood species are commonly used for exterior fencing due to durability?
• When a single gate is located at the corner of a fence, it should swing toward which position to be out of the way when open?
• A traditional method used to fasten wrought metal parts together is which of the following?
• If ponding occurs near gate posts, what issue is most likely to result?
• What is the value of a written scope of work in a fencing bid?
• According to ASTM specifications, all exposed ends of tubular posts should be fitted with caps of:
• If a fence section pulls loose from its anchor rod in a block wall, what is the recommended repair?
• Which device is used to bend sheet steel into the desired shape?
• End-post and terminal-post installation influences what?
• Why is drainage around footings important?
• Which method is best for connecting fabric to wrought iron fences?
• How are quantities of chain link fabric measured?
• Which components are part of a basic chain-link fence system?
• You are fastening a hinge to a wooden post. If the bolt must go through the post, what type of hinge would you use?
• Which coatings protect metal fences from corrosion in coastal environments?
• Panel boards on a wood retaining wall should be installed on the back of the posts.
• If corrosion is more of a maintenance concern than strength and rigidity, ___ ornamental fencing may be your best alternative
• If the bolt must pass through the post when fastening a hinge to a wood post, which hinge should be used?
• ___ ornamental fence systems offer superior corrosion resistance and low maintenance.
• Which bolt is best for a brace band?
• Where a grooved post and horizontal drop in boards are used, it is best to use a(n):
• One mile is equal to how many feet?
• There should be no __ where ornamental iron is installed onto or through wood.
• Which factors influence material waste allowances in a fencing project?
• Which of the following is not used with wood gates?
• What essential safety steps are required when digging footings?
• Power driven staples aren't permitted on:
• What is the consequence of poor compatibility between concrete mix, soil, and posts?
• What is the purpose of line stakes in laying out a fence?
• What are common scale options for plan drawings used in residential fencing projects?
• Gate openings on chain link fences are measured inside to inside. Which of the following is NOT a correct alternative measurement listed in typical practice?
• Hinges may be secured to metal gates in which of the following ways?
• What tool is listed as the best option for removing a post with a concrete base when a mechanical post puller is unavailable?
• What unit of measure is used for paying fence quantities (excluding gates)?
• Which components are commonly included in a takeoff for a chain-link fence?
• Which nut shape is used with machine screws besides squares?
• According to CalTrans specifications, gate latches must be:
• When an automatic backup warning device is used, it must be normally audible from a distance of how many feet?
• Installing chain link kennel panels to existing buildings may be done by attaching the panels using:
• What finish is recommended for iron surfaces after installation to protect from rust?
• Which distance conversion is correct for one mile in feet?
• Which sources should you review to determine fence line location and avoid disputes?
• Wood jambs for gates may be fastened to masonry walls with:
• What is a typical approach to aligning multiple gates along a fence line?
• What are common failure modes for vinyl fencing?
• What steps ensure proper gate alignment with metal fences?
• Which actions are taken before assembling metal pieces that touch?
• If a single gate is located at the corner of a fence, it should swing:
• Which of the following gate latches are padlockable?
• Which post type is typically driven into the ground?
• All iron surfaces should be ___ after assembly and installing them into wood posts or rails.
• Clearing the fence line consists of which of the following?
• According to CalTrans specs, how are fence quantities paid for (with the exception of gates) ?
• Which statement is most accurate about plan measurements in relation to the actual site?
• Which of the following is a correct sequence of safety and prep steps before pouring fence footing concrete?
• Which statement best describes the consequences of missing statutory deadlines in mechanics liens?
• Which factor is not typically considered when sizing post-hole diameter?
• Which installation step reduces the likelihood of post movement?
• A galvanized surface has been damaged. The contractor wire brushes the surface to remove the cracked coating, and then used spray paint to apply unthinned zinc rich paint to the cleaned areas. The contractor proceeded:
• Which orientation is correct for installing a tap?
• How many miles is 38 km?
• If a job requires 400 linear feet of fabric and 400 feet of top rail, how many pieces are needed if top rail comes in 21-foot lengths?
• Gate latches can be made from which materials?
• Under which condition is aluminum considered the best option for ornamental fencing?
• The easiest joint to use is the which joint?
• What is the purpose of a 'takeoff' in estimating fencing work from plans?
• Why is end-post and terminal-post installation critical for gate operation?
• Panel boards on a wood retaining wall should be installed on which side of the posts?
• What are common concrete mix considerations for fence footings?
• Which method is not listed for securing hinges to metal gates?
• Why is proper tensioning of chain-link fabric critical?
• When repairing damaged coatings, after galvanizing, welds shall be ground smooth and wire brushed to remove loose or burned zinc coating, after which the cleaned areas shall be prepared and neatly coated with which substance?
• Extending footings below the frost depth per local codes accomplishes what?
• What is the purpose of corrosion-resistant coatings on chain-link hardware?
• Why is frost depth important when designing fence footings?
• Which type of hinge may be used to flush-mount a gate with a narrow gate posts?
• What are the nails called that attach cover material directly to a fence frame?
• Which hardware practice aligns with vinyl installation guidance?
• What shape nut (besides squares) is used with machine screws?
• Why is it important to review specifications for fence style, height, and gate hardware in plans?
• All fittings, latches, rods, and other gate hardware shall be which of the following?
• Which document would you review to determine required gate hardware for a fence project?
• On sloped ground, which side should gates swing toward if possible?
• Which statement best describes rot-resistant wood use for fence posts?
• Which tools are recommended to maintain consistent gate alignment along a fence line?
• The type of bolt which has a coarse thread, a smooth round head and a black rough finish is the:
• Besides squares, what type of nut is used w machine screws?
• When estimating labor, which tasks should be included?
• How do you verify fence height compliance with code?
• Wood jambs for gates may be fastened to masonry walls with which combination of fasteners?
• Which state agency administers contractor licensing in California, including the C-13 class?
• Posts anchored in concrete may be removed by:
• Which practice best helps ensure posts remain upright and gate frames square during installation?
• Which of the following can be used to set steel posts?
• According to CalTrans, braces from each lot must be tested up to which number?
• Standard 9-gauge fabric requires less tension than which gauge?
• For tubed fence, such as welded, bent rail type, which tubing pairing is easier to work with?
• What is the primary purpose of the CSLB 'Law and Business' portion of the exam?
• You are fastening a hinge to a wooden gate post. If the bolt must go through the post, what type of hinge would you use?
• What is the role of tension bands in chain-link fencing?
• How should labor for fencing installation be priced?
• The best material for securing a steel post in a concrete hole is which of the following?
• According to CalTrans specifications, posts from each lot of how many posts or less must be tested, and braces from each lot of how many braces?
• Which statement about frost depth and footings is true?
• What are the nails to which cover material directly attached known as?
• Which of the following is a correct statement about 'H' posts?
• What is the purpose of using forms around fence post footings?
• The major ingredients in concrete are:
• How does chain-link fabric mesh size affect privacy and security?
• Which method is not listed for setting typical fence line posts in undisturbed earth?
• When laying out multiple gates, which practice supports consistent operation?
• On sloped ground, hang gates to swing toward which side if possible?
• What is a typical consideration for post-hole diameter relative to post size?
• What is the primary function of a gate post in a fence system?
• Standard 9-gauge fabric requires less tension than:
• Which finish is specified for all gate hardware to prevent corrosion?
• What safety features are required for automatic gate operators?
• Which hinge should be used to fasten a hinge to a wood gate post when the bolt must pass through the post?
• Double-drive gates are most often used on which type of ground?
• Which sign indicates potential UV damage in vinyl fencing?
• Why is corrosion-resistant fasteners important in metal fences?
• ____ ornamental fence is most widely used material but requires the most maintenance.
• What is the purpose of setting posts in concrete and adding bracing?
• What maintenance considerations should you address for wooden fences?
• Which of the following can be used to set steel posts?
• When repairing damaged coatings, all welds made after galvanizing shall be ground smooth and wire brushed; the cleaned areas shall be coated with which material?
• Which of the following posts may be driven?
• What is the typical requirement for clearance under a fence for accessibility or drainage?
• What factors influence gate swing versus sliding gate installation?
• How should gate hinges and latches be installed for durability?
• Properly stretched fabric won't ___.
• During vinyl fence installation, which practice helps prevent warping or buckling?